- You do not have any products in your shopping cart yet.
Lite cable connection, 6 primary pin
uniLIGHT.at UNICONNECT
The new uniCONNECT plug-in system uses massive blades and high-capacity sockets. Thanks to the new design, it is now finally possible to realize high numbers of poles in one connector with a small overall size - currently up to 22 pins. Over 3000 cycles are possible with loads up to 10A. Optimally designed for use in modelling.
The blades offer the advantage that all cables can be reliably and easily soldered without a plastic support being able to melt. There are also strain relief, detent, handle and anti-kink protection. The contacts of the blades are always visible, whereby damage and contamination can be recognized immediately.
The biggest advantage of the system is that, even in the plug, a double redundancy for important control functions is provided. For this reason, the system not only specifies conventional pin numbers, but also differentiates between primary pins (double, for main functions) and secondary pins (single, for light, landing gear, brake, ...).
Floating LITE is a reduced form of the well-known DIRECT connector. Ideal for small space applications such as oars or thin wings. The socket is equipped with increased contact force and is fully glued to a permanently elastic compound (silicone) to allow movement, the male connector is screwed on as usual.
The male connectors offer the advantage that all cables can be reliably and easily soldered without a plastic carrier being able to melt. The contacts of the male connectors are always visible, which means that damage and contamination can be recognized immediately. The greatest advantage of the system, however, is that double redundancy for important control functions is already provided in the connector. For this reason, not only conventional pin numbers are given in the system, but a distinction is made between primary pins (double, for main functions) and secondary pins (single, for light, chassis, brake, ...).
RTR as ready assembled and soldered unit with 2 / 3m cable connected directly 1 to 1. This is installed on one side, the length defined to the servo and assembled with crimp contacts. The remaining cable is laid on the other side to the receiver and assembled there. This finished unit is always delivered in one piece. 1xM and 1xF
DIY as a kit for the modeler with all parts and screws for the own construction. Thereby attractively prided and always delivered as a pair of 2 pieces, 2xM and 2xF
RTW as a pre-assembled connector to which only the cables have to be soldered - the assembly of the plates is already done. 2xM and 2xF are supplied
The new uniCONNECT plug-in system uses massive blades and high-capacity sockets. Thanks to the new design, it is now finally possible to realize high numbers of poles in one connector with a small overall size - currently up to 22 pins. Over 3000 cycles are possible with loads up to 10A. Optimally designed for use in modelling.
The blades offer the advantage that all cables can be reliably and easily soldered without a plastic support being able to melt. There are also strain relief, detent, handle and anti-kink protection. The contacts of the blades are always visible, whereby damage and contamination can be recognized immediately.
The biggest advantage of the system is that, even in the plug, a double redundancy for important control functions is provided. For this reason, the system not only specifies conventional pin numbers, but also differentiates between primary pins (double, for main functions) and secondary pins (single, for light, landing gear, brake, ...).
Floating LITE is a reduced form of the well-known DIRECT connector. Ideal for small space applications such as oars or thin wings. The socket is equipped with increased contact force and is fully glued to a permanently elastic compound (silicone) to allow movement, the male connector is screwed on as usual.
The male connectors offer the advantage that all cables can be reliably and easily soldered without a plastic carrier being able to melt. The contacts of the male connectors are always visible, which means that damage and contamination can be recognized immediately. The greatest advantage of the system, however, is that double redundancy for important control functions is already provided in the connector. For this reason, not only conventional pin numbers are given in the system, but a distinction is made between primary pins (double, for main functions) and secondary pins (single, for light, chassis, brake, ...).
RTR as ready assembled and soldered unit with 2 / 3m cable connected directly 1 to 1. This is installed on one side, the length defined to the servo and assembled with crimp contacts. The remaining cable is laid on the other side to the receiver and assembled there. This finished unit is always delivered in one piece. 1xM and 1xF
DIY as a kit for the modeler with all parts and screws for the own construction. Thereby attractively prided and always delivered as a pair of 2 pieces, 2xM and 2xF
RTW as a pre-assembled connector to which only the cables have to be soldered - the assembly of the plates is already done. 2xM and 2xF are supplied
assembled with cable:
- 6 primary contacts (redundant; for main-functions like servo)
- 3000 cycles, 10A for primary contacts
- strain and bend relief
- primary contacts
- double redundancy in socket
- free accessible contacts and solder points
- floating self contacting sockets
- ready assembled with 2m cable (0,25mm²)
- DIY Kit with all pieces and screwes
- cover measurment 7x28mm
- socket measurment 21x7x18mm
- weight without cable 9g
ready assembled:
- plug in system with 3 redundant pins for one primary servo (main functions)
- ready assembled with 2m cable connected directly 1to1
- 1 pair (m/f)
- 1 mounting stencil
- for plug in system with 3 redundant pins for one primary servo (main functions)
- for experienced constructors
- includes all pieces and screws for assembly
- 2 pair (m/f)
- 1 mounting stencil