- You do not have any products in your shopping cart yet.
Header cable connection, 3 primary pin
uniLIGHT.at UNICONNECT
The new uniCONNECT plug-in system uses massive blades and high-capacity sockets. Thanks to the new design, it is now finally possible to realize high numbers of poles in one connector with a small overall size - currently up to 22 pins. Over 3000 cycles are possible with loads up to 10A. Optimally designed for use in modelling.
The blades offer the advantage that all cables can be reliably and easily soldered without a plastic support being able to melt. There are also strain relief, detent, handle and anti-kink protection. The contacts of the blades are always visible, whereby damage and contamination can be recognized immediately.
The biggest advantage of the system is that, even in the plug, a double redundancy for important control functions is provided. For this reason, the system not only specifies conventional pin numbers, but also differentiates between primary pins (double, for main functions) and secondary pins (single, for light, landing gear, brake, ...).
Floating DIRECT & Floating HEADER are two groups of plug-in systems that were developed exclusively for the independent contacting of the wing and fuselage. There are no cables or plugs hanging around that could be damaged or dirty. The male connector is contacted directly with the socket during assembly. This is reliably possible with uniCONNECT, because the socket strips are not rigidly but “floating” connected to the carrier and can therefore move with slight movements and vibrations of the sash. Of course, the system is only suitable for rigidly screwed, right-angled and neatly routed connections. The connector cannot absorb any mechanical stress from an imprecise connector!
The two groups DIRECT and HEADER only differ in connection. DIRECT was primarily developed for reliable soldered connections, HEADER is prepared with normal pins for Uni plugs.
All plugs are screwed together from several high-quality fiberglass elements and can be dismantled and serviced at any time. Each connector is offered in two versions:
RTR as ready assembled and soldered unit with 2 / 3m cable connected directly 1 to 1. This is installed on one side, the length defined to the servo and assembled with crimp contacts. The remaining cable is laid on the other side to the receiver and assembled there. This finished unit is always delivered in one piece. 1xM and 1xF
DIY as a kit for the modeler with all parts and screws for the own construction. Thereby attractively prided and always delivered as a pair of 2 pieces, 2xM and 2xF
RTW as a pre-assembled connector to which only the cables have to be soldered - the assembly of the plates is already done. 2xM and 2xF are supplied
The new uniCONNECT plug-in system uses massive blades and high-capacity sockets. Thanks to the new design, it is now finally possible to realize high numbers of poles in one connector with a small overall size - currently up to 22 pins. Over 3000 cycles are possible with loads up to 10A. Optimally designed for use in modelling.
The blades offer the advantage that all cables can be reliably and easily soldered without a plastic support being able to melt. There are also strain relief, detent, handle and anti-kink protection. The contacts of the blades are always visible, whereby damage and contamination can be recognized immediately.
The biggest advantage of the system is that, even in the plug, a double redundancy for important control functions is provided. For this reason, the system not only specifies conventional pin numbers, but also differentiates between primary pins (double, for main functions) and secondary pins (single, for light, landing gear, brake, ...).
Floating DIRECT & Floating HEADER are two groups of plug-in systems that were developed exclusively for the independent contacting of the wing and fuselage. There are no cables or plugs hanging around that could be damaged or dirty. The male connector is contacted directly with the socket during assembly. This is reliably possible with uniCONNECT, because the socket strips are not rigidly but “floating” connected to the carrier and can therefore move with slight movements and vibrations of the sash. Of course, the system is only suitable for rigidly screwed, right-angled and neatly routed connections. The connector cannot absorb any mechanical stress from an imprecise connector!
The two groups DIRECT and HEADER only differ in connection. DIRECT was primarily developed for reliable soldered connections, HEADER is prepared with normal pins for Uni plugs.
All plugs are screwed together from several high-quality fiberglass elements and can be dismantled and serviced at any time. Each connector is offered in two versions:
RTR as ready assembled and soldered unit with 2 / 3m cable connected directly 1 to 1. This is installed on one side, the length defined to the servo and assembled with crimp contacts. The remaining cable is laid on the other side to the receiver and assembled there. This finished unit is always delivered in one piece. 1xM and 1xF
DIY as a kit for the modeler with all parts and screws for the own construction. Thereby attractively prided and always delivered as a pair of 2 pieces, 2xM and 2xF
RTW as a pre-assembled connector to which only the cables have to be soldered - the assembly of the plates is already done. 2xM and 2xF are supplied
assembled with cable:
- 3 primary contacts (redundant; for main-functions like servo)
- 3000 cycles, 10A for primary contacts
- strain and bend relief
- primary contacts
- double redundancy in socket
- free accessible contacts and solder points
- floating self contacting sockets
- ready assembled with uni sockets
- DIY Kit with all pieces and screwes
- cover measurment 15x28mm
- weight without cable 6g
ready assembled:
- plug in system with 3 redundant pins for one primary servo (main functions)
- 1 mounting stencil
- for plug in system with 3 redundant pins for one primary servo (main functions)
- for experienced constructors
- includes all pieces and screws for assembly
- 2 pieces
- 1 mounting stencil
