- You do not have any products in your shopping cart yet.
15mm PIN Navigation Light, 4x2W, T-Fuse
LED high-performance navigation light with 4W reference power for operation as a navigation light on a wide variety of models. The pen light is delivered pre-assembled and ready for use on a CNC-machined aluminum heat sink, and 2 high-strength polycarbonate caps are included for free use:
1x 15mm cylinder cap
1x 15mm round cap
The caps must be glued separately and some of them can also be painted in the color of the model. Any non-evaporating adhesive such as epoxy, Uhu Allplast, Uhu Por, silicone, Canopy Glue,...
The light is equipped with an integrated temperature fuse, which switches off at 65°C and activates itself again after it has cooled down. The thermal design is designed for operation as a position light in model aircraft with an operating time of 5-8 minutes. Depending on the color of the model and the ambient temperature, it may switch off. Air cooling or increased aluminum mass can affect performance.
1x 15mm cylinder cap
1x 15mm round cap
The caps must be glued separately and some of them can also be painted in the color of the model. Any non-evaporating adhesive such as epoxy, Uhu Allplast, Uhu Por, silicone, Canopy Glue,...
The light is equipped with an integrated temperature fuse, which switches off at 65°C and activates itself again after it has cooled down. The thermal design is designed for operation as a position light in model aircraft with an operating time of 5-8 minutes. Depending on the color of the model and the ambient temperature, it may switch off. Air cooling or increased aluminum mass can affect performance.
Electricity: 16W reference power, 8(12)V, 1.3A
Beam angle: >160°
Light intensity: ~400 Lumen RED
Light intensity: ~600 Lumen GREEN
Light intensity: ~1100 Lumen WHITE
Dimension cooling tube: D 8mm, flange 10mm
Dimension light cap: round 15x10mm, cylindric 15x15mm
Total mass: D15mm, 47mm length
Weight: 7g (without cable)
Beam angle: >160°
Light intensity: ~400 Lumen RED
Light intensity: ~600 Lumen GREEN
Light intensity: ~1100 Lumen WHITE
Dimension cooling tube: D 8mm, flange 10mm
Dimension light cap: round 15x10mm, cylindric 15x15mm
Total mass: D15mm, 47mm length
Weight: 7g (without cable)
Ready to use with 1m silicon cable and series resistor for 2S, resistor for 3S enclosed
incl 2 caps (cylindrical and round)
incl 2 caps (cylindrical and round)
The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.
The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.
Note: The LED lights are extremely bright! Never look directly into a LED!
The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.
Note: The LED lights are extremely bright! Never look directly into a LED!
TECHNICAL INFORMATION
CONNECTION
CONNECTION
Customer reviews
Unfortunately there are no review yet. Be the first who rate this product.
You must be logged in to submit a review. Login
